Dashcam Setup?
If you dont mind me asking how did you go about installing the rear cam. Ive some excess cable left. Which trim did you use to hide it?
I installed my Thinkware Q800 pro.
I ran my cable on the right hand side of the door weather seal and trim.
all the excess wire I hid in the boot trim.
I did not take pictures of the whole installation, but here are a few pictures that shows the installation.
I used RODI tubing from my fish tank which is flexible and allowed to feed the wire through.
December 2022 = J12 1.5 Tekna e-power, Gun Metal Grey, Thinkware F800 Pro, Cellink Pro.
April 2017 = J11 1.2 N-Tec + DIG-T CVT 2016, Gun Metal Grey;
January 2015 = J10 1.6 Tekna DCI, Gun Metal Grey.
April 2017 = J11 1.2 N-Tec + DIG-T CVT 2016, Gun Metal Grey;
January 2015 = J10 1.6 Tekna DCI, Gun Metal Grey.
Hi,nitromax wrote: ↑Tue Jan 10, 2023 1:02 amI installed my Thinkware Q800 pro.
I ran my cable on the right hand side of the door weather seal and trim.
all the excess wire I hid in the boot trim.
20230106_142218.jpg
I did not take pictures of the whole installation, but here are a few pictures that shows the installation.
20230106_141557.jpg
20230106_141549.jpg
I used RODI tubing from my fish tank which is flexible and allowed to feed the wire through.
20230106_133415.jpg
20230106_140507.jpg
Thanks for your reply.
How did you manage to route the cable on the inside on the boot. I tried to remove the parcel shelf trims but they were extremely tight fit and i left it at that. Was scared to break any clips etc.
Thanks
Hi,ST09 wrote: ↑Tue Jan 10, 2023 11:54 amHi,nitromax wrote: ↑Tue Jan 10, 2023 1:02 amI installed my Thinkware Q800 pro.
I ran my cable on the right hand side of the door weather seal and trim.
all the excess wire I hid in the boot trim.
20230106_142218.jpg
I did not take pictures of the whole installation, but here are a few pictures that shows the installation.
20230106_141557.jpg
20230106_141549.jpg
I used RODI tubing from my fish tank which is flexible and allowed to feed the wire through.
20230106_133415.jpg
20230106_140507.jpg
Thanks for your reply.
How did you manage to route the cable on the inside on the boot. I tried to remove the parcel shelf trims but they were extremely tight fit and i left it at that. Was scared to break any clips etc.
Thanks
I did not take any trim out on the inside. I ran the wire on right hand side all the way to the boot rubber weather strip, I tucked the wire into the plastic trim to hide it.
When I got to the rubber weather strip I carefully prised the roof liner down a bit and then I took the rubber gromit off that hides the tubing for the rear washer. I then used a flexible tubing to feed it from inside of the car where the roof lining is and pushing it upwards. (imagine a square, from the bottom left of the square to the top right of the square.) in that angle and the red tubing I used came out near the opening where the rubber gromit was.
I then taped the wire to the tubing and pulled it through, all nicely tucked away out of sight.
December 2022 = J12 1.5 Tekna e-power, Gun Metal Grey, Thinkware F800 Pro, Cellink Pro.
April 2017 = J11 1.2 N-Tec + DIG-T CVT 2016, Gun Metal Grey;
January 2015 = J10 1.6 Tekna DCI, Gun Metal Grey.
April 2017 = J11 1.2 N-Tec + DIG-T CVT 2016, Gun Metal Grey;
January 2015 = J10 1.6 Tekna DCI, Gun Metal Grey.